Tricalcium phosphate (TCP) is one of the most widely used bioceramics for constructing bone tissue engineering scaffold. The three-dimensional (3D) printed TCP scaffold has precise and controllable pore structure, while with the limitation of insufficient mechanical properties. In this study, we investigated the effect of sintering temperature on the mechanical properties of 3D-printed TCP scaffolds in detail, due to the important role of the sintering process on the mechanical properties of bioceramic scaffolds. The morphology, mass and volume shrinkage, porosity, mechanical properties and degradation property of the scaffold was studied. The results showed that the scaffold sintered at 1 150℃ had the maximum volume shrinkage, the minimum porosity and optimal mechanical strength, with the compressive strength of (6.52 ± 0.84) MPa and the compressive modulus of (100.08 ± 18.6) MPa, which could meet the requirements of human cancellous bone. In addition, the 1 150℃ sintered scaffold degraded most slowly in the acidic environment compared to the scaffolds sintered at the other temperatures, demonstrating its optimal mechanical stability over long-term implantation. The scaffold can support bone mesenchymal stem cells (BMSCs) adherence and rapid proliferation and has good biocompatibility. In summary, this paper optimizes the sintering process of 3D printed TCP scaffold and improves its mechanical properties, which lays a foundation for its application as a load-bearing bone.
ObjectiveTo evaluate the biological effect on vascularization during bone repair of prevascularized porous β-tricalcium phosphate (β-TCP) tissue engineered bone (hereinafter referred to as prevascularized tissue engineered bone), which was established by co-culture of endothelial progenitor cells (EPCs) and bone marrow mesenchymal stem cells (BMSCs) based on tissue engineering technology. Methods EPCs and BMSCs were isolated from iliac bone marrow of New Zealand white rabbits by density gradient centrifugation and differential adhesion method. The cells were identified by immunophenotypic detection, BMSCs-induced differentiation, and EPCs phagocytosis. After identification, the third-generation cells were selected for subsequent experiments. First, in vitro tubule formation in EPCs/BMSCs direct contact co-culture (EPCs/BMSCs group) was detected by Matrigel tubule formation assay and single EPCs (EPCs group) as control. Then, the prevascularized tissue engineered bone were established by co-culture of EPCs/BMSCs in porous β-TCP scaffolds for 7 days (EPCs/BMSCs group), taking EPCs in porous β-TCP scaffolds as a control (EPCs group). Scanning electron microscopy and laser scanning confocal microscopy were used to observe the adhesion, proliferation, and tube formation of cells. Femoral condyle defect models of 12 New Zealand white rabbits were used for implantation of prevascularized tissue engineered bone as the experimental group (n=6) and porous β-TCP scaffold as the control group (n=6). The process of vascularization of β-TCP scaffolds were observed. The numbers, diameter, and area fraction of neovascularization were quantitatively evaluated by Microfill perfusion, Micro-CT scanning, and vascular imaging under fluorescence at 4 and 8 weeks. ResultsThe isolated cells were BMSCs and EPCs through identification. EPCs/BMSCs co-culture gradually formed tubular structure. The number of tubules and branches, and the total length of tubules formed in the EPCs/BMSCs group were significantly more than those in the EPCs group on Matrigel (P<0.05) after 6 hours. After implanting and culturing in porous β-TCP scaffold for 7 days, EPCs formed cell membrane structure and attached to the material in EPCs group, and the cells attached more tightly, cell layers were thicker, the number of cells and the formation of tubular structures were significantly more in the EPCs/BMSCs group than in the EPCs group. At 4 weeks after implantation, neovascularization was observed in both groups. At 8 weeks, remodeling of neovascularization occurred in both groups. The number, diameter, and area fraction of neovascularization in the experimental group were higher than those in the control group (P<0.05), except for area fraction at 4 weeks after implantation (P>0.05). ConclusionThe prevascularized tissue engineered bone based on direct contact co-culture of BMSCs and EPCs can significantly promote the early vascularization process during bone defects repair.
Objective To investigate the ability of plateletrich plasma(PRP) combined with cells and artificial bone in accelerating the repair of bone defect. Methods The marrow stromal stem cells (MSCs) of rabbit were cultured and induced into the osteoblast-like cells in vitro. PRP was produced with low-density twice centrifugations. Forty-eight New Zealand rabbits were made 1.2 cm bilateral radius defect models and divided into 4 groups averagely at random: group A(left:PRP/MSCs/β-tricalcium phosphate(β-TCP), right: MSCs/β-TCP), group B (left:autoradius, right: PRP/MSCs/β-TCP); group C (left:autoradius,right: MSCs/β-TCP), and group D(left:PRP/β-TCP; right:β-TCP). At 2, 6 and 12 weeks after operation, the repair of bone defect was evaluated by the generalobservation, histology, biomechanics and histomorphology. Results There was a stable platelet concentration in PRP and it was about 5.45±0.23 times of whole blood. In the aspect of bone bridge and conture of the defects, at 2 and 6 weeks, PRP/MSCs/β-TCP and MSCs/β-TCP displayed asimilar outcome and were less than auto in general sample and X-ray;at12 weeks,PRP/MSCs/β-TCP was similar to autoradius and better than MSCs/β-TCP.in the aspect of quantity and quality of bone formation,histology showed that PRP/MSCs/β-TCP and autoradius were better than MSCs/β-TCP(P<0.05),and there was nosignificantdifference between PRP/MSCs/β-TCP and autoradius(P>0.05). At 2 and 6 weeks,there was no significant difference between PRP/β-TCP and β-TCP(P>0.05)。At 12 weeks,PRP/β-TCP was better than β-TCP(P<0.05). In the aspect of intensity f bone formation,at 6 and 12 weeks,PRP/MSCs/β-TCP and autoradiuswere better than MSCs/β-TCP(P<0.05). At 6 weeks,autoradius was better than PRP/MSCs/β-TCP(P<0.05). At 12 weeks,there was no significant difference between PRP/MSCs/β-TCP and auto(P>0.05). PRP/TCP and β-TCP had no significant difference at 12 weeks(P>0.05). Conclusion PRP/MSCs/β-TCP demonstrated excellent ability of forming bone in experiment. PRP was most likely to accelerate the repair of bone defect through increasing the activity of proliferation and differentiationof MSCs and osteoblasts.
Objective To investigate the influence of different dose levels of hydroxyapatite/tricalcium phosphate (HA/TCP) on the proliferation and alkalinephosphatase (ALP) activity of rabbit osteoblasts. Methods Three different doselevels of HA/TCP (10%, 40%, 70%) were co-cultivated with rabbit osteoblasts respectively. The proliferation and ALP expression capacity of osteoblasts were examined with MTT method and enzyme histochemistry once every 24 hours until 5 days. Three control groups of other materials were treated and examined in the sameway: rabbit osteoblasts as normal control; polyvinylchloride as positive control; titanium alloy as negative control. Results There was remarkable timeeffect relationship in the proliferation of osteoblasts. Ten percent HA/TCP did not affect osteoblasts growth while 40% HA/TCP could slow the cell growth rate down though time-effect relationship still existed. The proliferation of osteoblasts stagnated when co-cultivated with 70% HA/TCP. On the other hand, 10% HA/TCP could cause reversible damage on ALP activity of osteoblasts, whereas when the dose was40%, and the cultivation lasted 6 days the damage was irreversible. Three different dose levels of titanium alloy (10%, 40%, 70%) had no effect on the proliferation or ALP activity of osteoblasts. Conclusion Dosage is an important factor affecting the biocompatibility evaluation of biomaterial. It suggests that dose choosing should be more specified upon each individual biomaterial. It also indicates that ALP may be a good supplementary index of the cell compatibility of material.
ObjectiveTo improve the poor mechanical strength of porous ceramic scaffold, an integrated method based on three-dimensional (3-D) printing technique is developed to incorporate the controlled double-channel porous structure into the polylactic acid/β-tricalcium phosphate (PLA/β-TCP) reinforced composite scaffolds (double-channel composite scaffold) to improve their tissue regeneration capability and the mechanical properties. MethodsThe designed double-channel structure inside the ceramic scaffold consisted of both primary and secondary micropipes, which parallel but un-connected. The set of primary channels was used for cell ingrowth, while the set of secondary channels was used for the PLA perfusion. Integration technology of 3-D printing technique and gel-casting was firstly used to fabricate the double-channel ceramic scaffolds. PLA/β-TCP composite scaffolds were obtained by the polymer gravity perfusion process to pour PLA solution into the double-channel ceramic scaffolds through the secondary channel set. Microscope, porosity, and mechanical experiments for the standard samples were used to evaluate the composite properties. The ceramic scaffold with only the primary channel (single-channel scaffold) was also prepared as a control. ResultsMorphology observation results showed that there was no PLA inside the primary channels of the double-channel composite scaffolds but a dense interface layer between PLA and β-TCP obviously formed on the inner wall of the secondary channels by the PLA penetration during the perfusion process. Finite element simulation found that the compressive strength of the double-channel composite scaffold was less than that of the single-channel scaffold; however, mechanical tests found that the maximum compressive strength of the double-channel composite scaffold[(21.25±1.15) MPa] was higher than that of the single-channel scaffold[(9.76±0.64) MPa]. ConclusionThe double-channel composite scaffolds fabricated by 3-D printing technique have controlled complex micropipes and can significantly enhance mechanical properties, which is a promising strategy to solve the contradiction of strength and high-porosity of the ceramic scaffolds for the bone tissue engineering application.
Objective To observe the effect of cationic liposomal ceftazidime (CLC) combined with nano-hydroxyapatite/β-tricalcium phosphate (n-HA/β-TCP) in the treatment of chronic osteomyelitis of rabbits. Methods Thirty healthy New Zealand white rabbits (4-6 months old; weighing, 2-3 kg) were selected to prepare the chronic osteomyelitis models. After 4 weeks, the gross observation, X-ray examination, and bacteriological and histopathological examinations were done; the models were made successfully in 27 rabbits. Of 27 rabbits, 24 were randomly divided into 4 groups (n=6): only debridement was performed in group A; ceftazidime was given (90 mg/kg), twice a day for 8 weeks after debridement in group B; ceftazidime and n-HA/β-TC were implanted after debridement in group C; and CLC and n-HA/β-TCP were implanted after debridement in group D. Before and after treatments, X-ray examination was done, and Norden score was recorded. At 8 weeks after treatment, the specimens were harvested for gross observation and for gross bone pathological score (GBPS) using Rissing standard; half of the specimens was used for histological observation and Smeltzer scoring, the other half for bacteriological examination and calculation of the positive rate of bacteria culture. Results At 8 weeks after treatment, Norden score of group D was significantly lower than that of groups A, B, and C (P lt; 0.05), but no significant difference was found among groups A, B, and C (P gt; 0.05). At 8 weeks after treatment, sinus healed in groups C and D, but sinus was observed in groups A and B; the GBPS scores of groups C and D were significantly lower than those of groups A and B (P lt; 0.05). The Smeltzer scores of groups C and D were significantly lower than those of groups A and B (P lt; 0.05). The positive rates of bacteria culture of groups C (0) and D (0) were significantly lower than those of group A (25.0%) and group B (16.7%) (P lt; 0.05). Conclusion CLC combined with n-HA/β-TCP has good effect in treating chronic osteomyelitis of rabbits, and it has better effect in treating chronic osteomyelitis of rabbits than ceftazidime with n-HA/β-TCP.
Objective To explore a novel nanometer biomaterial which could induce the regeneration of tooth tissues intell igently, and to evaluate the feasibil ity of using this kind of biomaterial as the scaffold for tooth tissue engineering by investigating the role it plays in tooth tissue engineering. Methods The scaffold for tooth tissue engineering containing recombinant human bone morphogenetic protein 2 (rhBMP-2) was prepared by mixing nanoscale β tricalcium phosphate (β-TCP)/collagen particles. Forty-six 8-10 weeks old specific pathogen free Sprague Dawley (SD)rats, including 34 females and 12 males, weighing 250-300 g, were involved in this study. Tooth germs were removed under a stereomicroscope from the mandible of newborn SD rat, then digested and suspended. Scanning electronic microscope (SEM), adhesion rate of cells, and MTT assay were used to evaluate the effects of the scaffold on the tooth germ cells cultured in vitro. The tissue engineered tooth germ which was constructed by tooth germ cells and scaffold was transplanted under SD rat’s kidney capsule as the experimental group (n=12); the tooth germ cells (cell-control group, n=12) or scaffold without cells (material-control group, n=4) were transplanted separately as control groups Specimens were harvested to perform general and histological observations at 4 and 8 weeks after transplantation. Results β-TCP/collagen showed a loose and porous appearance with soft texture and excellent hydrophil icity. Tooth germ cells grew well and could attach to the scaffold tightly 3 days after coculture. The adhesion rates of tooth germ cells were 27.20% ± 2.37%, 44.52% ± 1.87%, and 73.81% ± 4.15% when cocultured with scaffold for 4, 8, and 12 hours, respectively. MTT assay showed that the cell prol iferation status of experimental group was similar to that of the control group, showing no significant difference (P gt; 0.05). Some white calcified specimens could be harvested at 4-8 weeks after transplantation. At 4 weeks after transplantation some typical structures of dental cusp and enamel-dentin l ike tissues could be seen in the experimental group. Enamel-dentin l ike tissues also formed in some specimens of cell-control group, but they arranged irregularly. At 8 weeks after transplantation the enamel-dentin l ike tissue of experimental group exhibited a mature appearance and organized structure in comparison with that at 4 weeks. And mature enamel or dentin l ike tissue also could be seen in cell-control group. In contrast, there was no enamel or dentin l ike tissue in material-control group at 4 or 8 weeks after transplantation. Conclusion rhBMP-2 decorated β-TCP/collagen scaffold has good biocompatibil ity and can be used as a novel nanometer biomaterial, so it is a good choice in scaffolds for tooth tissue engineering.
Objective To review the research progress of strontium (Sr) modified β-tricalcium phosphate composite biomaterials (SrTCP) promoting osteogenesis through immune regulation, and provides reference and theoretical support for the further development and research of SrTCP bone repair materials in bone tissue engineering in the future. Methods The literature about SrTCP promoting osteogenesis through immune regulation at home and abroad in recent years was extensively reviewed, and the preparation methods, immune mechanism and application of promoting osteogenesis were summarized and analyzed. Results The preparation methods of SrTCP include solid-state reaction sintering method, solution combustion quenching method, direct doping method, ion substitution method, etc. SrTCP has immune regulatory effects, which can play an immune regulatory role in inducing macrophage polarization, inducing angiogenesis and anti oxidative stress to promote osteogenesis. ConclusionAt present, studies have shown that SrTCP can promote bone defect repair through immune regulation. Subsequent studies can start from the control of the optimal repair concentration and release rate of Sr, and further clarify the specific mechanism of SrTCP in promoting angiogenesis and anti oxidative stress, which is helpful to develop new materials for bone defect repair.
OBJECTIVE To manufacture adriamycin-porous tricalcium phosphate (A-PTCP) ceramic drug delivery system (DDS) as a possible method for bone defect treatment after bone tumor operation. METHODS A-PTCP DDS was made from putting adriamycin into PTCP. Thirty rabbits were divided randomly into group A(24 rabbits) and group B(6 rabbits). A-PTCP was implanted in the greater trochanter of the right femur in group A. Adriamycin were injected into veins in group B. Muscle around A-PTCP and plasma were taken out at different period. Adriamycin concentrations in muscle and plasma were measured by high performance liquid chromatography (HPLC). RESULTS A-PTCP could gradually release adriamycin over 10 weeks. Adriamycin concentrations in the muscle were higher than that in plasma. CONCLUSION A-PTCP may be a new method for repairing bone defects after bone tumor operation.
This study aims to explore the vascularization of hydroxyapatite/tricalcium phosphate (HA/TCP) biomaterials implanted in mice during osteoinduction. The HA/TCP biomaterials were implanted in muscle of mice, and 2, 4, 6, 8, 10 and 12 weeks after the implantation, the materials were harvested to prepare serial sections and hematoxylin-eosin (HE) staining. The process of vascularization was dynamically described, and the area percentage of neovascularization was quantitatively analyzed. The results showed that neovascularization formation was a continuous and dynamic process. The neovascularization appeared largely in the first two weeks, with a rising trend in week 4, reached peak in week 6, and gradually reduced in week 8. The results provide ideas for improving the success rate of bone tissue engineering, and indicate the mechanism of osteoinduction.