The repair of the long bone defects by combined grafting of homogenous deealcified bene matrix(DBM ) with centrally enveloped vascularized periosteum Was reported as a new techniqe. Theroentgenograms,bone mineral count and histologic examination were done. The results showed thatthis method was beneficial and had better effect on prornoting healing of the long bene defeets fromone stage operation The oporative proeedure was described on deatil It was considered that the homogenous DBM ...
Objective To fabricate a novel composite scaffold with acellular demineralized bone matrix/acellular nucleus pulposus matrix and to verify the feasibility of using it as a scaffold for intervertebral disc tissue engineering through detecting physical and chemical properties. Methods Pig proximal femoral cancellous bone rings (10 mm in external diameter, 5 mm in internal diameter, and 3 mm in thickness) were fabricated, and were dealed with degreasing, decalcification, and decellularization to prepare the annulus fibrosus phase of scaffold. Nucleus pulposus was taken from pig tails, decellularized with Triton X-100 and deoxycholic acid, crushed and centrifugalized to prepare nucleus pulposus extracellular mtrtix which was injected into the center of annulus fibrosus phase. Then the composite scaffold was freeze-dryed, cross-linked with ultraviolet radiation/carbodiimide and disinfected for use. The scaffold was investigated by general observation, HE staining, and scanning electron microscopy, as well as porosity measurement, water absorption rate, and compressive elastic modulus. Adipose-derived stem cells (ADSCs) were cultured with different concentrations of scaffold extract (25%, 50%, and 100%) to assess cytotoxicity of the scaffold. The cell viability of ADSCs seeded on the scaffold was detected by Live/Dead staining. Results The scaffold was white by general observation. The HE staining revealed that there was no cell fragments on the scaffold, and the dye homogeneously distributed. The scanning electron microscopy showed that the pore of the annulus fibrosus phase interconnected and the pore size was uniform; acellular nucleus pulposus matrix microfilament interconnected forming a uniform network structure, and the junction of the scaffold was closely connected. The novel porous scaffold had a good pore interconnectivity with (343.00 ± 88.25) µm pore diameter of the annulus fibrosus phase, 82.98% ± 7.02% porosity and 621.53% ± 53.31% water absorption rate. The biomechanical test showed that the compressive modulus of elasticity was (89.07 ± 8.73) kPa. The MTT test indicated that scaffold extract had no influence on cell proliferation. Live/Dead staining showed that ADSCs had a good proliferation on the scaffold and there was no dead cell. Conclusion Novel composite scaffold made of acellular demineralized bone matrix/acellular nucleus pulposus matrix has good pore diameter and porosity, biomechanical properties close to natural intervertebral disc, non-toxicity, and good biocompatibility, so it is a suitable scaffold for intervertebral disc tissue engineering.
ObjectiveTo investigate the effects of silencing P75 neurotrophin receptor (P75NTR) and nerve growth factor (NGF) overexpression on the proliferative activity and ectopic osteogenesis ability of bone marrow mesenchymal stem cells (BMSCs) combined with demineralized bone matrix for heterotopic osteogenesis.MethodsBMSCs of Sprague Dawley (SD) rats were cultured and passaged by adherent isolation method. The third generation BMSCs were transfected with lentivirus mediated P75NTR gene silencing (group B), NGF overexpression gene (group C), P75NTR silencing and NGF overexpression double genes (group D), respectively, and untransfected cells as control (group A). After 7 days of transfection, the expression of fluorescent protein of the target gene was observed by fluorescence microscope; cell counting kit 8 method was used to detect the cells activity for 8 days after transfection; the expressions of P75NTR and NGF proteins in each group were detected by Western blot. The adhesion of BMSCs to demineralized bone matrix (DBM) was observed by inverted phase contrast microscope and scanning electron microscope after transfection of p75NTR silencing and NGF overexpression double genes. After transfection, BMSCs and DBM were co-cultured to prepare 4 groups of tissue engineered bone, which were respectively placed in the dorsal subcutaneous tissue of 8-week-old SD rats to construct subcutaneous ectopic osteogenesis model (n=6). HE staining was performed at 4 and 8 weeks after operation. ALP staining was used to observe the formation of calcium nodules at 8 weeks after operation. The expressions of Runt-related transcription factor 2 (Runx2), alkaline phosphatase (ALP), and osteocalcin (OCN) were detected by real-time fluorescent quantitative PCR.ResultsAt 7 days after transfection, there was no fluorescence expression in group A, red fluorescence expression was seen in group B, green fluorescence expression in group C, and red-green compound fluorescence expression in group D. The fluorescence expression rate of target gene was about 70%. Western blot detection showed that the relative expression of P75NTR protein in groups A and C was significantly higher than that in groups B and D, and the relative expression of NGF protein in groups C and D was significantly higher than that in groups A and B (P<0.05). With the passage of time, the cell proliferation activity increased in all groups, especially in group D, which was significantly higher than that in group A at 3-8 days (P<0.05). The results of inverted phase contrast microscope and scanning electron microscope showed that BMSCs could adhere well to DBM. In the subcutaneous ectopic osteogenesis experiment, HE staining showed that at 4 and 8 weeks after operation, the more bone tissue was formed in group D than in the other 3 groups. ALP staining showed that group D had the highest ALP activity and better osteogenic expression. Compared with group A, the relative expressions of Runx2, ALP, and OCN mRNAs in group D were significantly higher than those in group A (P<0.05).ConclusionSilencing P75NTR and NGF overexpression double genes co-transfected BMSCs with DBM to construct tissue engineered bone has good ectopic osteogenic ability. By increasing NGF level and closing P75NTR apoptosis channel, it can not only improve cell activity, but also promote bone tissue regeneration.
Objective To explore the method of fabricating freeze-dried demineralized bone matrix with nanoscale topography (nFDBM) and to investigate the feasibility of reconstruction of tissueengineered bone with the novel scaffold. Methods Allogenic dogs’ phalangeal cortical bone was fabricatedinto freeze-dried demineralized bone (FDBM) with modified Urist’s method. FDBM was subjected toNd∶YAG laser irradiation under special conditions. The surface topography was identified by atomic force microscope(AFM) and scanning electron microscope (SEM). The osteoblasts were induced from autologous mesenchymal stem cells (MSCs) and mixed with nFDBM and FDBM in vitro.The effects of the different topography oncellbehavior was identified by SEM. The complex of nFDBM and osteoblasts wereimplanted into fascial bags on dogs’ back (experimental group A) and dogs’ phalangeal defects on right (experimental group C), while FDBMosteoblast complex (control group B) and unique FDBM (control group D) were implanted into the corresponding sites on left as control groups. The osteogenic status was assessed by X-ray, HE and SEM at 4, 8 and 12 weeks after surgery. Results The surface of FDBM subjected to Nd∶YAG laser irradiation resulted in well-defined three-dimensional nanoscale grooves (150 nm in depth and 600 to 800 nm in width). When the osteoblasts were implanted on the scaffold, the cells adhering to nFDBM were morethan those to FDBM and secreted more extracellular matrix. Either new bone-likethin layer on the nanoscale surface or a lot of new boneformation inner the experimental complex was observed by HE after 12 weeks of surgery and the experimental complexes were partially calcified at the same time, while the control groups almost had no osteogenic phenomena. Conclusion Nd∶YAG laser could produce nanoscale grooves on the FDBM surface. The nanoscale grooves are conductive to adherence, proliferation and matrix secretion of osteoblasts. Complexes by tissue engineering and nanoscale technology have some osteogenic abilities in vivoafter implanted the animal model.
Objective To evaluate the effect of implantation of the complex of high viscous chitosan/glycerol phosphate with demineral ized bone matrix (HV-C/GP-DBM) in repairing cartilage defects of rabbits. Methods HV-C/ GPDBM was prepared by compounding HV-C/GP and DBM by 2:1 (W/W). Twenty-four 34-week-old New Zealand white adult rabbits, weighing 3.5-4.5 kg, were included. A bit with the diameter of 3.5 mm was used to drill 3-cm-deep holes in both sides of femoral condyle to make cartilage defects. The complex of HV-C/GP-DBM was then injected into the right holes as the experimental group and the left ones serve as the control group. The rabbits were killed at 4, 8 and 16 weeks after theoperation, respectively. The obtained specimens were observed macroscopically, microscopically and histologically. According to the International Cartilage Repair Society Histological Scoring (ICRS), the effect of cartilage repair was assessed at 16 weeks postoperatively. Results At 4-8 weeks postoperatively, in the experimental group, the defects were filled with hyal ine cartilage-l ike tissues; the majority of chitosan degradated; and the DBM particles were partly absorbed. However, in the control group, there were small quantities of discontinuous fibrous tissues and maldistributed chondrocytes at the border and the bottom of the defects. At 16 weeks postoperatively, 6 joints in the experimental group had smooth surface, and the defects were basically repaired by hyal ine cartilage-l ike tissues. The newly-formed tissues integrated well with the surrounding area. Under the cartilage, the new bone formation was still active and some DBM particles could be seen. However, the defects in the control group were repaired by fibrous tissues. The result of histological scoring of the specimens at 16 weeks showed that a total of 6 aspects including formation of chondrocytes and integration with the surrounding cartilages were superior in the experimental group to those in the control group, and there were significant differences between the two groups (P lt; 0.05). Conclusion The biodegradable and injectable complex of HV-C/GP-DBM with good histocompatibil ity and non-toxic side effects can repair cartilage defects and is a promising biomaterial for cartilage defect repair.
Objective To evaluate the adhesion, prol iferation and osteogenic differentiation of rabbit BMSCs after cultured on freeze-dried demineral ized bone matrix (FDBM) modified with type II cadherin ectodomain (Cad- II). Methods BMSCs isolated from 10 Japanese white rabbits (male and female, 4-week-old, 0.61-0.88 kg) were cultured. The second generation of BMSCs (cell density 1 × 106 /mL) were seeded onto the Cad-II modified allogenic FDBM (experimental group) and only FDBM (control group) respectively, and then cocultured in vitro. The densities of seeded cells, the adhesion rate and their ALP activity were measured. The complex was observed through inverted phase contrast microscope and scanning electron microscope to evaluate the interaction between cells and FDBM. Another group of second generation of BMSCs (cell density 5 × 105 /mL) were seeded onto the Cad-II modified FDBM (experimental group) and only FDBM (control group) respectively, and then cocultured in vitro too. The ALP activity and osteocalcin immunohistochemical was measured. Results There was no significant difference in cell prol iferation between experimental group and control group. The adhesion rate of cells in the experimental group was 87.41% ± 5.19%, higher than that in the the control group 35.56% ± 1.75% (P lt; 0.01); the densities of seeded cells reached 5.0 × 105, showing significant difference compared with the control group (2.6 × 104, P lt; 0.05). Inverted phase contrast microscope showed that in the experimental group, more cultured BMSCs pasted in the hole and edge of the scaffold than that in the control group. HE staining showed the densities of seeded cells in the experimental group was higher than that in the control group. Scanning electron microscope showed that in the experimental group, a lot of cultured BMSCs adhered, spreaded in the scaffold, in the control group only a few BMSCs unevenly distributed in the scaffold. After 7 days of culture, the cultured BMSCs on modified FDBM expressed higher ALP activity; after 14 days of culture, the ALP activity (29.33 ± 1.53) was higher than that cultured on unmodified FDBM (18.31 ± 1.32), the positive rates of osteocucl in were 83% ± 7% in the experimental group and 56% ± 7% in the control group, showing significant difference (P lt; 0.01). Conclusion Cad-II enhanced cell adhesion to FDBM and promoted BMSCs differentiate to osteoblast, but no obvious effects were observed in cell prol iferation.
Objective To evaluate the tissue response induced by three kinds of bone transplantation materials implanted in rat so as to provide proper evidence for their cl inical appl ication. Methods Thirty-six healthy mature Sprague- Dawly mice, weighing from 229 g to 358 g, were randomly assigned to groups A and B (n=18). Three kinds of materials wereimplanted into muscles of rats. Calcium sulfate (CS) granular preparations and allogeneic demineral ized bone matrix (DBM) were transplanted into the left (group A1) and right (group A2) thigh muscle pouches of group A. Respectively, whereas xenogenic DBM were transplanted into the left (group B1) thigh muscle pouches of group B and the right (group B2) sites were taken as control without implant. The samples (n=6) were collected to make the observation of gross and histology and to analyze histological score after 2, 4, and 6 weeks. Results The gross observation: implanted materials were gradually absorbed at late stage in group A1. No obvious degradation and absorption, but fibrosis of tissues were observed in group A2 and B1. The inflammatory reactions were more severe in groups A2 and B1. In group B2, only the changes of scar were seen at operative site. The histological observation: no obvious inflammatory reactions were seen in group A1, CS were gradually absorbed and completely absorbed at 6 weeks, while fibrosis of tissues increased at late stage. Inflammatory reactions in group A2 and group B1 were alleviated gradually, no obvious absorption and degradation were observed. The different two DBM could induce granulation tissues and bone formation at different sites and secondary fibrosis with no obvious immune response was observed. In group B2, there was an increase in collagen fiber density and angiogenesis at late stage. The scores of inflammatory infiltration were significantly higher in groups A2, B1 than in groups A1, B2 (P lt; 0.05), and the scores of fibrosis was larger in groups A1, A2 and B1 than in group B2 (P lt; 0.05). Conclusion CS has rapid dissolution and good biocompatibil ity. It is a good replaceable packing materials of bone defects in some upper l imb’s or acute bone fracture. Both of two DBM have biocompatibil ity and osteoinductive potential, which dissolution are very slow. Due to these capacity, they can be served as an ideal materials in treatment of lower l imb’s bone defect and nonunion.
Because of its high biological compatibility, titanium has been a good biomaterial. The implanted artificial bone made from titanium can contact with the vital and mature osseous tissue directly within 3-6 months, the so-called osteointergration. In order to promote the process of osteointergration, FDBM of rabbit was prepared and was combined with pure titanium so as to speed up osteointergration. The study focused on bone density, bone intergration rate, new bone growth rate around the pure titanium, and the Ca2+ and PO(4)3- density of titanium-bone interface. A control group of pure titanium inplant without FDBM was set up. The results showed FDBM had no antigenicity. It could induce and speed up the new bone formation at titanium-bone interface. The titanium-bone intergration time was within 2 months. It was suggested that there were more bone morphogenesis protein (BMP) or other bone induction and bone formation factors in brephobone than that in child and adult bone. As a kind of bone induction material, FDBM was easy prepared, cheap in price, easy to storage, no antigenicity and obvious bone-inductive function.
OBJECTIVE To investigate the feasibility of freeze-dried demineralized bone matrix (FDBM) as scaffold material in bone tissue engineering. METHODS Osteoblasts which were isolated from cranial periosteum of New Zealand rabbits were cultured as the seeding cells, then the cells were cocultured with heterogenous FDBM in vitro. The cell-material complex was observed under phase microscope, light microscope and electronic scanning microscope in order to evaluate the interaction between cells and FDBM. RESULTS Eight hours after coculture, the osteoblasts adhered to FDBM scaffolds. Seven days later, the osteoblasts differentiated and proliferated in FDBM network. Extracellular matrix was secreted and calcium nodes were formed among osteoblasts. CONCLUSION FDBM is a good scaffold material for the bone tissue engineering.